Skip Nav Destination
1-12 of 12
Proc. ASME. IMECE97, Manufacturing Science and Engineering: Volume 1, 113-119, November 16–21, 1997
Paper No: IMECE1997-1083
...Abstract Abstract This paper describes a new electromagnetic contact sensing technique called the “Fine Touch” method which enables the cutting tool itself to be used as a probe during on-machine measurement of parts. The simple sensor design of the probe (the cutting tool) has resulted...
Proc. ASME. IMECE2020, Volume 2B: Advanced Manufacturing, V02BT02A065, November 16–19, 2020
Paper No: IMECE2020-24515
...Abstract Abstract When the geometry of a non-rigid part or pre-assembly is measured fully clamped (over-constrained) in a measurement fixture, the spring-back information and influence from gravity forces are usually lost in the collected data. From the 3D-measurement data, it is hard...
Proc. ASME. IMECE2020, Volume 5: Biomedical and Biotechnology, V005T05A025, November 16–19, 2020
Paper No: IMECE2020-24184
... that can measure its self-acceleration, angular velocity, and quaternions to collect human movement data continuously for long-term. Additionally, we collected the arm movement data of 30 participants using the developed device. The participants of this study carried on with their normal lives...
Proc. ASME. IMECE2019, Volume 5: Engineering Education, V005T07A006, November 11–14, 2019
Paper No: IMECE2019-11038
...BEAUTIFUL MUSIC IN THE CLASSROOM: MARIMBA AS A LAB EXPERIMENT FOR TEACHING VIBRATION MEASUREMENT Mathew Schaefer1 Milwaukee School of Engineering Milwaukee, WI ABSTRACT A marimba bar makes a rich and vibrant sound when played by a skilled musician. When that same marimba bar is played...
Proc. ASME. IMECE2009, Volume 4: Design and Manufacturing, 99-104, November 13–19, 2009
Paper No: IMECE2009-10160
... 07 07 2010 In the present work, a prototype machine was developed for film thickness measurement for tribological tests. The configuration of the machine was based Block on Ring (BOR) technique. In the current machine, frictional forces and film thickness were measured using load cell...
Proc. ASME. IMECE2007, Volume 3: Design and Manufacturing, 517-522, November 11–15, 2007
Paper No: IMECE2007-44013
... pad is one of the critical factors in planarizing wafer surfaces and its properties play critical roles in polishing. However, pad properties change during the process. This paper reviews the measurement methods for thickness, hardness, and Young’s modulus of polishing pads. Chemical mechanical...
Proc. ASME. IMECE2003, Heat Transfer, Volume 1, 431-435, November 15–21, 2003
Paper No: IMECE2003-42906
... 13 05 2008 This paper presents a new technique for measuring the non-uniformity of circumferential distribution of fuel by means of laser transmission beam for fuel nozzle. Using this technique, the physical and mathematical relationships have been developed and validated...
Proc. ASME. IMECE2003, Design Engineering, Volumes 1 and 2, 601-610, November 15–21, 2003
Paper No: IMECE2003-41620
... during the compression process to calculate the air pressure in the vane segments. The air pressure was used with Newton’s law to calculate loads acting on bearings and vanes. A compressor and experimental setup were also built to measure the radial load acting on the bearings. The measured load acting...
Proc. ASME. IMECE2003, Fluids Engineering, 243-248, November 15–21, 2003
Paper No: IMECE2003-41351
... 13 05 2008 This study introduces an experimental method that can measure air pressures in the vane segments when a sliding-vane rotary compressor performs suction and compression phases in stable or unstable rotational speeds. When the air pressures of these two phases can be measured...
Proc. ASME. IMECE2005, Heat Transfer, Part A, 775-779, November 5–11, 2005
Paper No: IMECE2005-82247
... agreement. USB-WLAN thermal optimization CFD simulation measurement Methodology for thermal measurement, JEDEC JESD51 series. Flotherm Version 5.1, Flomerics Inc., Marlborough, MA, 2004 SPIL Presentation, Internal Eason Chen, Carol Liang, Jeng Yuan Lai, Yu-Po Wang, C.S. Hsiao...
Proc. ASME. IMECE2005, Noise Control and Acoustics, 277-280, November 5–11, 2005
Paper No: IMECE2005-80705
..., by using the measurement and analysis system, we measured the sound pressures levels and their curves the noise of a military diesel engine, then made spectral analysis and coherence analysis. The results provide bases for low noise design of this diesel engine. diesel engine noise characteristics...
Proc. ASME. IMECE2006, Heat Transfer, Volume 3, 147-152, November 5–10, 2006
Paper No: IMECE2006-13934
.... thermoelectrics nanowires measurement Li D. , Huxtable S. , Abramson A. , Majumdar A. , 2005 , “ Thermal Transport in Nanostructured Solid-State Cooling Devices ,” Journal of Heat Transfer , 127 , pp. 108 – 114 . Shakouri A. , Zhang Y. , 2005 , “ On-Chip Solid-State...