1-17 of 17
Keywords: internal pressure
Close
Sort by
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. August 2023, 145(4): 041304.
Paper No: PVT-22-1032
Published Online: May 25, 2023
... the test data to within (−6%, +10%). These results are far better than all the previous. 05 03 2022 20 04 2023 25 05 2023 internal pressure ultimate tensile strength (UTS) plastic load plastic instability structural integrity torispheres Emergency situations occur right...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. December 2019, 141(6): 061702.
Paper No: PVT-19-1026
Published Online: October 9, 2019
... between the data sets is 0.95 that shows accurate predictions in FEM results. e-mail:  chunqing.li@rmit.edu.au 05 02 2019 31 08 2019 00 00 0000 09 10 2019 unsaturated soils buried pipes finite element analyses stress prediction traffic load internal pressure...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. June 2019, 141(3): 031203.
Paper No: PVT-18-1161
Published Online: March 21, 2019
... internal pressure, and the comparison of the current design codes for buckling design is shown in Table 2 . It can be seen that ASME NH provides design factors for both instantaneous buckling and creep buckling design but no analysis method is provided in this code. Regarding ASME VIII-1, a method based...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. December 2018, 140(6): 061203.
Paper No: PVT-17-1248
Published Online: November 12, 2018
... into the behavior of proposed API 12F tanks exposed to higher internal pressure and vacuum pressure. Temporary storage of relatively small amounts of oil upon extraction in the upstream segment of oil and gas industry is typically accomplished by cylindrical aboveground steel storage tanks that are transportable...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. April 2017, 139(2): 021205.
Paper No: PVT-15-1264
Published Online: September 28, 2016
... to study, in a comprehensive manner, the stress behavior in internally pressurized cylindrical vessels intersected by radial cylindrical nozzles. The limitation of the shell solution for cylindrical pressure vessels with small-diameter nozzles is addressed by the use of solid elements based on the theory...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. June 2015, 137(3): 031011.
Paper No: PVT-14-1019
Published Online: June 1, 2015
... of inelastic response of pressurized piping system under seismic loading. Shake table test has been carried out on a three-dimensional stainless steel piping system under internal pressure and seismic load. The amplitude of base excitation has been increased till failure of the piping system. The tested piping...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Codes And Standards
J. Pressure Vessel Technol. August 2012, 134(4): 041101.
Published Online: July 27, 2012
... depth and the internal pressure increase and the value of maximum membrane strain in the circumferential direction could be significant depending on the dent depth and internal pressure combinations. The largest value of this strain component was obtained when the internal pressure and the dent depth...
Journal Articles
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. June 2010, 132(3): 031701.
Published Online: April 28, 2010
... to lateral load in addition to internal pressure and axial load. Four full-scale laboratory tests were conducted, and it was found that the application of lateral load on wrinkled pipe produces a wrinkle shape similar to that occurred in a field NPS10 line pipe. Complex test setup was designed and built...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. June 2009, 131(3): 031401.
Published Online: February 11, 2009
...Jinyang Zheng; Xiang Li; Ping Xu; Xiufeng Lin; Yaxian Li Plastic pipe reinforced by cross helically wound steel wires, namely PSP, is a new plastic-matrix steel composite pipe developed in China recently. In order to understand the mechanical properties of PSP under internal pressure, a four-layer...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. May 2008, 130(2): 021702.
Published Online: March 17, 2008
... and high internal pressures on X52 grade steel pipes with a diameter-to-thickness ratio of 45 show that this pipeline is extremely ductile and did not rupture under axisymmetric compressive axial deformation. However, they fail due to the excessive cross-sectional deformation and the final deformed shape...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. August 2006, 128(3): 454–461.
Published Online: November 18, 2005
...Guillermo Ramirez; Michael D. Engelhardt; Timothy J. Fowler This paper proposes a method for determining endurance limits to leakage for fiberglass pipes under internal pressure using acoustic emission signals and static pressure tests. Results are presented from a series of cyclic internal...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. May 2005, 127(2): 151–156.
Published Online: May 27, 2005
...J. Błachut Tests on two internally pressurized toroidal shells are described in this paper. These were laboratory scale models manufactured by welding 90°, 316L steel elbows. The outside diameter of the toroids was about 310.0 mm, radius of the tube was about 41.0 mm, and the wall thickness...